The Lateral Mass Cervical Plate (13 mm) is a titanium spinal fixation implant designed for use as part of a compatible cervical spine internal fixation system, providing a multi-point plate-and-screw construct for lateral mass fixation according to the approved indications and surgical technique.
The implant features an elongated multi-hole plate geometry with fixation openings distributed along its longitudinal axis. These holes are designed to receive compatible cervical fixation screws and provide multiple fixation points according to the required construct configuration and number of targeted vertebral levels.
According to the supplied catalog information, the plate is manufactured from:
Material: Titanium
The product family is listed under:
Cat. No.: AMS 514.013.000
The plate is available in seven configurations, ranging from 2 holes to 8 holes, allowing the surgeon to select an appropriate configuration according to cervical anatomy, number of fixation points, targeted vertebral levels, required plate coverage, and intraoperative requirements.
Each configuration carries an individual Cat. No. and GTIN No., supporting accurate implant identification, product traceability, surgical set preparation, procurement, inventory management, and stock control.
Product Explanation
The Lateral Mass Cervical Plate is a spinal fixation plate used within a compatible cervical stabilization system.
A simplified fixation concept can be represented as:
Cervical Vertebrae → Compatible Cervical Screws → Lateral Mass Cervical Plate → Cervical Fixation Construct
The plate provides multiple screw fixation interfaces along its length, allowing the fixation construct to be selected according to the number and location of the vertebral segments included in the surgical plan.
The catalog identifies this product specifically as:
Lateral Mass Cervical Plate (13 mm)
The supplied information does not define exactly what the 13 mm dimension represents; therefore, it should not be described as plate width, hole spacing, or another dimensional parameter without confirmation from the technical datasheet.
Product Components and Design
- Titanium Plate Body
The primary structural component is manufactured from Titanium, according to the supplied product information.
The plate body provides the structural interface for the compatible screw fixation construct.
- Multiple Fixation Holes
The plate family is available with:
- 2 Holes
- 3 Holes
- 4 Holes
- 5 Holes
- 6 Holes
- 7 Holes
- 8 Holes
These openings serve as fixation interfaces for compatible cervical screws.
- Straight Multi-Hole Geometry
The implant features an elongated plate geometry with fixation holes arranged along its longitudinal axis.
This provides several plate configurations for different fixation requirements.
- Contoured Plate Profile
The supplied image shows a contoured external plate profile surrounding the screw openings.
The exact anatomical curvature, plate contour specifications, and bending characteristics are not stated in the supplied data.
- Configuration-Specific Design
Each variant is defined by its number of holes and is assigned an individual Cat. No. and GTIN No.
Intended Use
The Lateral Mass Cervical Plate (13 mm) is designed for use within compatible cervical spine fixation systems according to the manufacturer’s approved indications and Instructions for Use.
Potential applications, when included within the approved indications, may include:
- Cervical spine stabilization.
- Lateral mass fixation constructs.
- Cervical plate-and-screw fixation.
- Multi-level cervical fixation constructs.
- Cervical spinal reconstruction procedures.
- Internal stabilization of appropriate cervical vertebral segments.
Selection of the appropriate plate configuration depends on:
- Cervical anatomy.
- Number of fixation points.
- Targeted vertebral levels.
- Screw positioning.
- Required plate coverage.
- Bone quality.
- Preoperative planning.
- Intraoperative assessment.
The implant should be selected and implanted by a qualified spine surgeon according to the approved surgical technique and IFU.
Key Benefits
Titanium Material
The product is specified as:
Material: Titanium
according to the supplied catalog data.
Multiple Hole Configurations
Available configurations include:
2H / 3H / 4H / 5H / 6H / 7H / 8H
providing multiple options for different cervical fixation constructs.
Seven Product Configurations
The product family includes:
7 individual configurations
within one plate system.
Multi-Point Fixation Geometry
The plate incorporates multiple screw fixation interfaces distributed along its length.
Cervical Construct Flexibility
Different hole counts support implant selection according to the required number of fixation points and targeted cervical levels.
Structured Implant Identification
Each plate configuration has a dedicated product code for:
- Implant identification.
- Surgical set preparation.
- Procurement.
- Inventory management.
Product Traceability
Each configuration also has an individual GTIN No. to support:
- Product traceability.
- Inventory tracking.
- Stock control.
- Supply chain management.
Technical Specifications
| No. of Holes | Cat. No. | GTIN No. |
| 2H | AMS 514.013.002T | 6221361043633 |
| 3H | AMS 514.013.003T | 6221361045484 |
| 4H | AMS 514.013.004T | 6221361045491 |
| 5H | AMS 514.013.005T | 6221361043664 |
| 6H | AMS 514.013.006T | 6221361043671 |
| 7H | AMS 514.013.007T | 6221361043688 |
| 8H | AMS 514.013.008T | 6221361043695 |
Technical Overview
Product Name: Lateral Mass Cervical Plate (13 mm)
Material: Titanium
Product Type: Cervical Spine Fixation Plate
Product Category: Spinal Internal Fixation Implant
General Cat. No.: AMS 514.013.000
Available Configurations: 2H / 3H / 4H / 5H / 6H / 7H / 8H
Number of Configurations: 7
Design: Straight Multi-Hole Cervical Plate
Fixation Concept: Plate-and-Screw Cervical Fixation
Anatomical Application: Cervical Spine
Identification: Individual Cat. No. and GTIN No. for each configuration
Product Features
- Lateral Mass Cervical Plate Design.
- Manufactured from Titanium according to the catalog.
- Designed for compatible cervical spine fixation systems.
- Straight multi-hole plate geometry.
- Available from 2 to 8 holes.
- Total of 7 product configurations.
- Provides multiple screw fixation interfaces.
- Supports different multi-point cervical fixation constructs.
- Offers several options for preoperative implant selection.
- Supports intraoperative configuration selection according to anatomy and surgical requirements.
- Individual Cat. No. for each hole configuration.
- Individual GTIN No. for each variant.
- Supports implant identification, traceability, procurement, and inventory management.
Reviews
There are no reviews yet.